531906-1EN_BEthernet NetworkingInstallation & Operations ManualEthernet NetworkingInstallation & Operations ManualGPSUnit 1Unit 2HUMMINBIRD®ET
A. Two 700 Series™ Units1. Insert the AS EC QDE Ethernet cable connector into theEthernet slot on the 700 Series™ cable collector. Repeat
3. Connect the AS EC QDE cable connector to the AS EC 10E cableconnector. 4. Hand-tighten the screw nut(s) on each cable to secure theconnect
800/900 Series™ (rear view)Ethernet Port1100 Series™ (rear view)6Installation
2. Powering OnWhen you have installed an Ethernet network, the power on process is thesame as powering on a single control head, however,
3. Configuring the Ethernet NetworkSet up your Humminbird® Ethernet Network using the following instructions,including these topics:1. Network Setup O
EthernetSpeedDigital ReadoutDualBeam PLUS™Transducer(Local)It will only report data to the 788ci HD.Side Imaging® Transducer(Local)It will only report
Network Menu TabWhen units are connected on thenetwork, the Network menu tab is addedto the Main Menu system. The Network menu tab includes the f
Customize the Unit NameEach control head is assigned a Unit Name, which is based on its modelnumber and serial number. The unit name is a
Open the Network Source Setup Dialog BoxThe Network Source Setup dialog box displays all of the sources connected tothe network. The sources may be sh
Sonar Source Overview When you select a new transducer source, the alarms, menu settings, viewrotation, and digital readouts will automatically upda
iThank You!Thank you for choosing Humminbird®, America's #1 name in Fishfinders.Humminbird® has built its reputation by designing
NOTE: The Shared and Local menu options may change to accommodate new productfeatures.Select a Sonar SourceWhen you first set up the network, the con
4. Select: Press the RIGHT Cursor key. The check mark indicates that thesource is being used by the control head. 5. Save: Press the EXIT key twic
Change the Sonar SourceTo change the sonar source, open the Network Source Setup dialog box andchange the transducer source at any time (see S
Temperature Source OverviewWhen you select a new temperature source, the alarms, menu settings, viewrotation, and digital readouts will automatically
Select a Temperature SourceTemperature sources can be detected from a transducer’s built-in temperaturefeature or from optional-purchase temperature/s
Select Temperature Sources for Digital Readout Boxes1. Open the Network Source Setup dialog box.2. Select the tab for T1, T2, T3, or T4: Press the RIG
6. Save: Press the EXIT key twice to close the dialog box. Networksettings are saved even after the unit is powered off. Local Setup: To u
Change the Temperature SourceTo change the temperature source after the network has been configured,open the Network Source Setup dialog box
Temperature Source Lost1100 Series™The Temp 2 (T2) Source is not detected on the network.22Temperature Sources
GPS and Sharing Waypoints OverviewWhen you select a new GPS source, the position, menu settings, view rotation,and digital readouts will automatically
NOTE: Some features discussed in this manual require a separate purchase, andsome features are only available on international models. Ever
Select a GPS SourceWhen you power on the network for the first time, the control head willautomatically choose the connected or internal
NOTE: The current GPS Fix Type is reported as No Fix, Fixed, or Enhanced. An Enhancedfix has been augmented using information from WAAS, EGNOS, or MSA
Change the GPS SourceTo change the GPS source after the network has been configured, open theNetwork Source Setup dialog box to change the GPS
Share WaypointsTo share waypoints on the network, turn on Share Waypoints on each controlhead. You can then observe the following:• When a waypoint i
Restore Defaults (Setup Menu Tab)If you choose to restore defaults on a Humminbird® control head, it is importantto note that the menu settings, inclu
TroubleshootingBefore contacting the Humminbird® Customer Resource Center, please readthe following section. Taking the time to review t
Fishing System Defaults to Simulator with a Transducer AttachedA connected and functioning transducer will cause the newly-started FishingSystem to go
Humminbird® AccessoriesAccessories customize your Fishing System to your needs and enable you tostay on the edge of new technology. When an accessory
Downriggers are the key to catching fish you otherwise couldn’t even touch. Andnow Humminbird’s CannonLink™ Downrigger Controller makes operation of u
Contact Humminbird®Contact the Humminbird® Customer Resource Center in any of the following ways:By Telephone:(Monday - Friday 8:00 a.m. to 4:30 p.m.
Table of ContentsiiiIntroduction 11. Installing an Ethernet Connection 22. Powering On 73. Configuring the Ethernet Network 8Configuration Overview 8N
Table of ContentsivTroubleshooting 29Fishing System Doesn’t Power Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Fishing S
IntroductionThis manual will guide you through the following network setup instructions: 1. Connect two Humminbird® units together2. Power On3. Config
1. Installing an Ethernet ConnectionIf your Humminbird® control head has a built-in Ethernet connector, the unitcan be connected to the Ethernet
NOTE: The AS EC [length]E cable is available in a variety of lengths. To purchase theEthernet Connect Cables or extension cables, visit our Web site a
Comments to this Manuals